Gas station technology - "safe - rational"

Steland-products - high-quality and elaborate solutions, that have proved themselves over many years. (remote filling stations, insular edges, fuel dispenser - base tanks, manhole pit covers)

Steel- and iron sheet construction - "economical - flexible". Steland constructs and uses many alternatives to make a solution that is custom-made for the customer - from mass productions to individual production. ( poles, pole encasement, gas station-service stations, metal profiling, painting)

Ready-mixed concrete wreath

Description:

• outer edges with attached bevel for polysulfid join
• concrete is fuel dense ; KIWA / KOMO BRL 2316
• non-skid rhomb-structural pattern
• capacity according to DIN 1072, loading case SLW 60 for abnormal load
• construction-conditioned no drain gutter needed
• 3 unscrewable stems M16 at the outer edges as suspension point

Advantages compared to site-mixed concrete

• shorter construction time
• cost benefit
• immediate polysulfid-jointing towards road and pavement possible
• ease of the height adjustments of the whole upper part
• no danger of deformation of the steel frame while concreting

Remote filling station with surface discharge

Description and advantages:

• to install into a highboard with discharge through the insular edge - or with lower edge discharge on road level
• vertical pipe outlets allow to pick lay-direction and lay-depth
• leaking liquid in the coupling area is getting diverted through the sloped tank bottom to the sealed road
• rainproof cover plate, with eyelet for the lock, integrated sash lock is possible
• opening of the hood is supported with gas pressure spring
• 4 height adjustable, galvanized sustain feet as assembling aid
• competely manufactured of steel sheet, chassis liquid-tight welded and inspected
• whole shaft is galvanized, tubes are not galvanized
• additional expoid-coating of the chassis, ca. 150*m

Manhole pit cover DIN EN 124 - D 400 KN, especially for gas station services

Description and advantages:

• very resilient according to DIN EN 124 class D 400 KN (ca. 40 to)
• particular big entrance area (800 x 800 mm)
• steel frame and lid completely galvanized, clamp and hinge axis made of stainless steel
• free working space because of almost vertical lid opening
• no risk of injury through slippery bottom of the lid; avoidance of unwelcome support bracket in the entering area
• easy to open and close because gas springs are used
• Precipitation protection for tank filling in the rain because the lower lid with applied force during the filling process is allowed to settle on the tubes.
• the geometry of the cover frame with extensive checker plate cover allows a rain-proof manhole covering without sensitive rubber seals.
• if installed correctly, there is density against constant rain and surface water up to 14 mm
• concrete is fuel dense, quality B35, surface color nature
• concrete-outer edge with attached bevel for polysulfid join
• 3 unscrewable stems M16 on the outer edges as attachment point

Remote filling shaft 2000 - acessible

Description and Advantages:

• type to connect double-walled steel filling pipes 3"/4", Flexwell-filling pipes DN 80 or synthetic pipe system
• rainproof manhole cover without sensitive rubber seals
• if installed correctly, there is density against constant rain and surface water up to 14 mm
• edge of the cover is sunk-in into the skid profile -> no risk of stumbling
• opening of the hood is supported with gas pressure springs
• chassis and frame of the lid are made of sheet steel
• liquid-tight welded and tested
• manhole completely galvanized, pipes non-galvanized

Remote filling shaft 2000 - trafficable

Description and Advantages:

=> like "accesible remote filling shaft" - additional one more feature

• particular high carrying capacity (at least 250 KN; ca.25 to) because of an optimized bracing system

• made from 3 mms of steel metal, liquid-close welded
• completely hot-dip galvanised, if requested with protective spraying
• foolproof catching of resigning leakage liquids and their visible surface derivation through rectangle-outlet canals by the island edge on the sealed roadway
• height-adjustable, hot-dip galvanised supporting feet
• solvable, liquid-thick and gasproof pipe penetrations (protected system) under retention of the electric potential separation between pipe system and columns and shaft system
• foundation frame can be cancelled, because all connection positions of the petrol pump foot are prepared with tapped holes
• relief of the pipe and concrete work; before pipes have been put in with their telescopic supporting feet to straightened tubs define according to the column default:
  - the tank island upper edges
  - the precise positions of all conduits
  - the height mass of the flange connections under the column (esp. Stencils)

Island-/ Highboardframes made of steel
Description:

• Steel-high board verges for pouring out with concrete
• completely precast kit for the easy screw montage on site
• all screw connections are invisible from the outside because of work-sided dowel pins
• executions to the installation in the roadway or to the construction on the roadway with height adjustments

Advantages towards beton-highboardbricks or base tiles:

• quick assembly, only one person necessary
• low weights, therefore no heave devices are needed
• easy positioning and adjustment
• density proof is cancelled (e.g., in the filling station area)
• varied special forms
• heights to 360 mms available

Technical data:

• materials high-grade steel 1.4301
• steel metals
• surfaces from high-grade steel 1.4301 IIIC shiningly, with protective foil for assembly and transport (normal case)
• steel hot-dip galvanised, natur
• hot-dip galvanised, undercoats (standard)
• hot-dip galvanised, varnished (RAL colours by customer wish)
• application cases profile height of big island height => prefabrication of the roadway surface against the island (ideal with concrete roadway)
• profile height of small island height => to the additional construction on the existing roadway
• for the balance of the roadway slope height-adjustable, bulkhead tins wedged from the inside (ideal with plaster roadway)

standard-island verges to the construction on the roadway

The most often demanded executions we can offer as inexpensive standard articles; divergent need we ask according to the preceding descriptions as special solutions with ourselves to ask for.

Description and advantages:

• application case - for construction on roadway
• with height-adjustable, wedged from the inside bulkhead tins as slope compensates
• connection and ground connection by means of inside-recumbent, hot-dip galvanised connection profiles
• island consisting of two curve pieces and two medium pieces
• all screw connections invisible from the outside through inside-recumbent high-grade steel dowel pins
• phase 10 x 45 ° in lower edge bulkhead metal for the fixing of the polysulfide joint to the roadway
• material - high-grade steel 1.4301
• surfaces IIIC - shiningly - with protective foil 80 mms for assembly and transport
• form - ovally
• profile with outside bulge 25 mms at the upper edge